Advertisement

The Light Emitting Diode

The Light Emitting Diode

Light Emitting Diodes or simply LED´s, are among the most widely used of all the different types of semiconductor diodes available today and are commonly used in TV’s and colour displays.

The light emitting diode is the most visible type of semiconductor diode. They emit a fairly narrow bandwidth of either visible light at different coloured wavelengths, invisible infra-red light for remote controls or laser type light when a forward current is passed through them.

The “Light Emitting Diode” or LED as it is more commonly called, is basically just a specialised type of diode as they have very similar electrical characteristics to a PN junction diode. This means that an LED will pass current in its forward direction but block the flow of current in the reverse direction.

Light emitting diodes are made from a very thin layer of fairly heavily doped semiconductor material and depending on the semiconductor material used and the amount of doping, when forward biased an LED will emit a coloured light at a particular spectral wavelength.

When the diode is forward biased, electrons from the semiconductors conduction band recombine with holes from the valence band releasing sufficient energy to produce photons which emit a monochromatic (single colour) of light. Because of this thin layer a reasonable number of these photons can leave the junction and radiate away producing a coloured light output.

light emitting diode construction

LED Construction

Then we can say that when operated in a forward biased direction Light Emitting Diodes are semiconductor devices that convert electrical energy into light energy.

The construction of a Light Emitting Diode is very different from that of a normal signal diode. The PN junction of an LED is surrounded by a transparent, hard plastic epoxy resin hemispherical shaped shell or body which protects the LED from both vibration and shock.

Surprisingly, an LED junction does not actually emit that much light so the epoxy resin body is constructed in such a way that the photons of light emitted by the junction are reflected away from the surrounding substrate base to which the diode is attached and are focused upwards through the domed top of the LED, which itself acts like a lens concentrating the amount of light. This is why the emitted light appears to be brightest at the top of the LED.

However, not all LEDs are made with a hemispherical shaped dome for their epoxy shell. Some indication LEDs have a rectangular or cylindrical shaped construction that has a flat surface on top or their body is shaped into a bar or arrow. Generally, all LED’s are manufactured with two legs protruding from the bottom of the body.

Also, nearly all modern light emitting diodes have their cathode, (  ) terminal identified by either a notch or flat spot on the body or by the cathode lead being shorter than the other as the anode ( + ) lead is longer than the cathode (k).

Unlike normal incandescent lamps and bulbs which generate large amounts of heat when illuminated, the light emitting diode produces a “cold” generation of light which leads to high efficiencies than the normal “light bulb” because most of the generated energy radiates away within the visible spectrum. Because LEDs are solid-state devices, they can be extremely small and durable and provide much longer lamp life than normal light sources.

Light Emitting Diode Colours

So how does a light emitting diode get its colour. Unlike normal signal diodes which are made for detection or power rectification, and which are made from either Germanium or Silicon semiconductor materials, Light Emitting Diodes are made from exotic semiconductor compounds such as Gallium Arsenide (GaAs), Gallium Phosphide (GaP), Gallium Arsenide Phosphide (GaAsP), Silicon Carbide (SiC) or Gallium Indium Nitride (GaInN) all mixed together at different ratios to produce a distinct wavelength of colour.

Different LED compounds emit light in specific regions of the visible light spectrum and therefore produce different intensity levels. The exact choice of the semiconductor material used will determine the overall wavelength of the photon light emissions and therefore the resulting colour of the light emitted.

Light Emitting Diode Colours

Typical LED Characteristics
Semiconductor
Material
Wavelength Colour VF @ 20mA
GaAs 850-940nm Infra-Red 1.2v
GaAsP 630-660nm Red 1.8v
GaAsP 605-620nm Amber 2.0v
GaAsP:N 585-595nm Yellow 2.2v
AlGaP 550-570nm Green 3.5v
SiC 430-505nm Blue 3.6v
GaInN 450nm White 4.0v

Thus, the actual colour of a light emitting diode is determined by the wavelength of the light emitted, which in turn is determined by the actual semiconductor compound used in forming the PN junction during manufacture.

Therefore the colour of the light emitted by an LED is NOT determined by the colouring of the LED’s plastic body although these are slightly coloured to both enhance the light output and to indicate its colour when its not being illuminated by an electrical supply.

Light emitting diodes are available in a wide range of colours with the most common being RED, AMBER,  YELLOW  and GREEN and are thus widely used as visual indicators and as moving light displays.

Recently developed blue and white coloured LEDs are also available but these tend to be much more expensive than the normal standard colours due to the production costs of mixing together two or more complementary colours at an exact ratio within the semiconductor compound and also by injecting nitrogen atoms into the crystal structure during the doping process.

From the table above we can see that the main P-type dopant used in the manufacture of Light Emitting Diodes is Gallium (Ga, atomic number 31) and that the main N-type dopant used is Arsenic (As, atomic number 33) giving the resulting compound of Gallium Arsenide (GaAs) crystalline structure.

The problem with using Gallium Arsenide on its own as the semiconductor compound is that it radiates large amounts of low brightness infra-red radiation (850nm-940nm approx.) from its junction when a forward current is flowing through it.

The amount of infra-red light it produces is okay for television remote controls but not very useful if we want to use the LED as an indicating light. But by adding Phosphorus (P, atomic number 15), as a third dopant the overall wavelength of the emitted radiation is reduced to below 680nm giving visible red light to the human eye. Further refinements in the doping process of the PN junction have resulted in a range of colours spanning the spectrum of visible light as we have seen above as well as infra-red and ultra-violet wavelengths.

By mixing together a variety of semiconductor, metal and gas compounds the following list of LEDs can be produced.

Types of Light Emitting Diode

  • Gallium Arsenide (GaAs) – infra-red
  • Gallium Arsenide Phosphide (GaAsP) – red to infra-red, orange
  • Aluminium Gallium Arsenide Phosphide (AlGaAsP) – high-brightness red, orange-red, orange, and yellow
  • Gallium Phosphide (GaP) – red, yellow and green
  • Aluminium Gallium Phosphide (AlGaP) – green
  • Gallium Nitride (GaN) – green, emerald green
  • Gallium Indium Nitride (GaInN) – near ultraviolet, bluish-green and blue
  • Silicon Carbide (SiC) – blue as a substrate
  • Zinc Selenide (ZnSe) – blue
  • Aluminium Gallium Nitride (AlGaN) – ultraviolet

Like conventional PN junction diodes, light emitting diodes are current-dependent devices with its forward voltage drop VF, depending on the semiconductor compound (its light colour) and on the forward biased LED current. Most common LED’s require a forward operating voltage of between approximately 1.2 to 3.6 volts with a forward current rating of about 10 to 30 mA, with 12 to 20 mA being the most common range.

Both the forward operating voltage and forward current vary depending on the semiconductor material used but the point where conduction begins and light is produced is about 1.2V for a standard red LED to about 3.6V for a blue LED.

The exact voltage drop will of course depend on the manufacturer because of the different dopant materials and wavelengths used. The voltage drop across the LED at a particular current value, for example 20mA, will also depend on the initial conduction VF point. As an LED is effectively a diode, its forward current to voltage characteristics curves can be plotted for each diode colour as shown below.

Light Emitting Diodes I-V Characteristics.

light emitting diode

Light Emitting Diode (LED) Schematic symbol and I-V Characteristics Curves
showing the different colours available.

Before a light emitting diode can “emit” any form of light it needs a current to flow through it, as it is a current dependant device with their light output intensity being directly proportional to the forward current flowing through the LED.

As the LED is to be connected in a forward bias condition across a power supply it should be current limited using a series resistor to protect it from excessive current flow. Never connect an LED directly to a battery or power supply as it will be destroyed almost instantly because too much current will pass through and burn it out.

From the table above we can see that each LED has its own forward voltage drop across the PN junction and this parameter which is determined by the semiconductor material used, is the forward voltage drop for a specified amount of forward conduction current, typically for a forward current of 20mA.

In most cases LEDs are operated from a low voltage DC supply, with a series resistor, RS used to limit the forward current to a safe value from say 5mA for a simple LED indicator to 30mA or more where a high brightness light output is needed.

LED Series Resistance.

The series resistor value RS is calculated by simply using Ohm´s Law, by knowing the required forward current IF of the LED, the supply voltage VS across the combination and the expected forward voltage drop of the LED, VF at the required current level, the current limiting resistor is calculated as:

LED Series Resistor Circuit

light emitting diode circuit

Light Emitting Diode Example No1

An amber coloured LED with a forward volt drop of 2 volts is to be connected to a 5.0v stabilised DC power supply. Using the circuit above calculate the value of the series resistor required to limit the forward current to less than 10mA. Also calculate the current flowing through the diode if a 100Ω series resistor is used instead of the calculated first.

1). series resistor required at 10mA.

light emitting diode series resistor

2). with a 100Ω series resistor.

led current

We remember from the Resistors tutorials, that resistors come in standard preferred values. Our first calculation above shows that to limit the current flowing through the LED to 10mA exactly, we would require a 300Ω resistor. In the E12 series of resistors there is no 300Ω resistor so we would need to choose the next highest value, which is 330Ω. A quick re-calculation shows the new forward current value is now 9.1mA, and this is ok.

Connecting LEDs Together in Series

We can connect LED’s together in series to increase the number required or to increase the light level when used in displays. As with series resistors, LED’s connected in series all have the same forward current, IF flowing through them as just one. As all the LEDs connected in series pass the same current it is generally best if they are all of the same colour or type.

Connecting LED’s in Series

leds connected in series

Although the LED series chain has the same current flowing through it, the series voltage drop across them needs to be considered when calculating the required resistance of the current limiting resistor, RS. If we assume that each LED has a voltage drop across it when illuminated of 1.2 volts, then the voltage drop across all three will be 3 x 1.2v = 3.6 volts.

If we also assume that the three LEDs are to be illuminated from the same 5 volt logic device or supply with a forward current of about 10mA, the same as above. Then the voltage drop across the resistor, RS and its resistance value will be calculated as:

series led current limiting resistor

Again, in the E12 (10% tolerance) series of resistors there is no 140Ω resistor so we would need to choose the next highest value, which is 150Ω.

LED Driver Circuits

Now that we know what is an LED, we need some way of controlling it by switching it “ON” and “OFF”. The output stages of both TTL and CMOS logic gates can both source and sink useful amounts of current therefore can be used to drive an LED. Normal integrated circuits (ICs) have an output drive current of up to 50mA in the sink mode configuration, but have an internally limited output current of about 30mA in the source mode configuration.

Either way the LED current must be limited to a safe value using a series resistor as we have already seen. Below are some examples of driving light emitting diodes using inverting ICs but the idea is the same for any type of integrated circuit output whether combinational or sequential.

IC Driver Circuit

led driver circuit

If more than one LED requires driving at the same time, such as in large LED arrays, or the load current is to high for the integrated circuit or we may just want to use discrete components instead of ICs, then an alternative way of driving the LEDs using either bipolar NPN or PNP transistors as switches is given below. Again as before, a series resistor, RS is required to limit the LED current.

Transistor Driver Circuit

led transistor driver

The brightness of a light emitting diode cannot be controlled by simply varying the current flowing through it. Allowing more current to flow through the LED will make it glow brighter but will also cause it to dissipate more heat. LEDs are designed to produce a set amount of light operating at a specific forward current ranging from about 10 to 20mA.

In situations where power savings are important, less current may be possible. However, reducing the current to below say 5mA may dim its light output too much or even turn the LED “OFF” completely. A much better way to control the brightness of LEDs is to use a control process known as “Pulse Width Modulation” or PWM, in which the LED is repeatedly turned “ON” and “OFF” at varying frequencies depending upon the required light intensity of the LED.

LED Light Intensity using PWM

pwm light control

When higher light outputs are required, a pulse width modulated current with a fairly short duty cycle (“ON-OFF” Ratio) allows the diode current and therefore the output light intensity to be increased significantly during the actual pulses, while still keeping the LEDs “average current level” and power dissipation within safe limits.

This “ON-OFF” flashing condition does not affect what is seen by the human eye as it “fills” in the gaps between the “ON” and “OFF” light pulses, providing the pulse frequency is high enough, making it appear as a continuous light output. So pulses at a frequency of 100Hz or more actually appear brighter to the eye than a continuous light of the same average intensity.

Multi-coloured Light Emitting Diode

LEDs are available in a wide range of shapes, colours and various sizes with different light output intensities available, with the most common (and cheapest to produce) being the standard 5mm Red Gallium Arsenide Phosphide (GaAsP) LED.

LED’s are also available in various “packages” arranged to produce both letters and numbers with the most common being that of the “seven segment display” arrangement.

Nowadays, full colour flat screen LED displays, hand held devices and TV’s are available which use a vast number of multicoloured LED’s all been driven directly by their own dedicated IC.

Most light emitting diodes produce just a single output of coloured light however, multi-coloured LEDs are now available that can produce a range of different colours from within a single device. Most of these are actually two or three LEDs fabricated within a single package.

Bi-colour Light Emitting Diodes

A bi-colour light emitting diode has two LEDs chips connected together in “inverse parallel” (one forwards, one backwards) combined in one single package. Bi-colour LEDs can produce any one of three colours for example, a red colour is emitted when the device is connected with current flowing in one direction and a green colour is emitted when it is biased in the other direction.

This type of bi-directional arrangement is useful for giving polarity indication, for example, the correct connection of batteries or power supplies etc. Also, a bi-directional current produces both colours mixed together as the two LEDs would take it in turn to illuminate if the device was connected (via a suitable resistor) to a low voltage, low frequency AC supply.

A Bi-colour LED

multi-coloured light emitting diode
LED
Selected
Terminal A AC
+
LED 1 ON OFF ON
LED 2 OFF ON ON
Colour Green Red Yellow

Tricoloured Light Emitting Diode

The most popular type of tricolour light emitting diode comprises of a single Red and a Green LED combined in one package with their cathode terminals connected together producing a three terminal device. They are called tricolour LEDs because they can give out a single red or a green colour by turning “ON” only one LED at a time.

These tricoloured LED’s can also generate additional shades of their primary colours (the third colour) such as Orange or Yellow by turning “ON” the two LEDs in different ratios of forward current as shown in the table thereby generating four different colours from just two diode junctions.

A Multi or Tricoloured LED

multi coloured led
Output
Colour
Red Orange Yellow Green
LED 1
Current
0 5mA 9.5mA 15mA
LED 2
Current
10mA 6.5mA 3.5mA 0

LED Displays

As well as individual colour or multi-colour LEDs, several light emitting diodes can be combined together within a single package to produce displays such as bargraphs, strips, arrays and seven segment displays.

A 7-segment LED display provides a very convenient way when decoded properly of displaying information or digital data in the form of numbers, letters or even alpha-numerical characters and as their name suggests, they consist of seven individual LEDs (the segments), within one single display package.

In order to produce the required numbers or characters from 0 to 9 and A to F respectively, on the display the correct combination of LED segments need to be illuminated. A standard seven segment LED display generally has eight input connections, one for each LED segment and one that acts as a common terminal or connection for all the internal segments.

  • The Common Cathode Display (CCD) – In the common cathode display, all the cathode connections of the LEDs are joined together and the individual segments are illuminated by application of a HIGH, logic “1” signal.
  • The Common Anode Display (CAD) – In the common anode display, all the anode connections of the LEDs are joined together and the individual segments are illuminated by connecting the terminals to a LOW, logic “0” signal.

A Typical Seven Segment LED Display

seven segment display

Opto-coupler

Finally, another useful application of light emitting diodes is in Opto-coupling. An opto-coupler or opto-isolator as it is also called, is a single electronic device that consists of a light emitting diode combined with either a photo-diode, photo-transistor or photo-triac to provide an optical signal path between an input connection and an output connection while maintaining electrical isolation between two circuits.

An opto-isolator consists of a light proof plastic body that has a typical breakdown voltages between the input (photo-diode) and the output (photo-transistor) circuit of up to 5000 volts. This electrical isolation is especially useful where the signal from a low voltage circuit such as a battery powered circuit, computer or microcontroller, is required to operate or control another external circuit operating at a potentially dangerous mains voltage.

Photo-diode and Photo-transistor Opto-couplers

led in opto-isolator

The two components used in an opto-isolator, an optical transmitter such as an infra-red emitting Gallium Arsenide LED and an optical receiver such as a photo-transistor are closely optically coupled and use light to send signals and/or information between its input and output. This allows information to be transferred between circuits without an electrical connection or common ground potential.

Opto-isolators are digital or switching devices, so they transfer either “ON-OFF” control signals or digital data. Analogue signals can be transferred by means of frequency or pulse-width modulation.

143 Comments

Join the conversation

Error! Please fill all fields.

  • C ASOKAN

    The graph shows current around 1ma even below 1 Volt. This is not correct. LEDS have micro amperes when the voltage is far enough from its threshold.

  • Richard

    Explanation is concise and clear

  • Vinay Kumar ojha

    Mujhe led ke colour ke bare me janana five led colour same voltage not over voltage

  • Jay

    Good 👍

  • Lakshman

    Very good explanation full of lots of important facts about leds! Thanks.

  • David G Ballenger

    I am making a breadboard for my great grand daughter that has a fascination for electric.

    Is there a diode that is one color and when you reverse the current it changes to another color?

    Thanks Dave

  • Banele

    I don’t see any characteristics of a light emitting diode

  • Harish Kumar

    Sir, I want to learn about LED and drivers , How they work as per series or drive r velues Regards SHUBHRA Light

  • andy

    I want to make a 12volt led lightboard for inside my truck, it would need around 100 bright white ,and 6 coloured stings of 25 bulbs each. Thing is i have no idea of how to do this and struggling to find any help on internet .Is anyone kind enough to help how to do this?

  • Kwame despite

    Good teaching

  • abdulwahab

    Contractors approaches you to design a circuit using semiconductor diodes, that shows voltage supply for alternate cycles of WAPDA electric supply at homes (for positive half cycle use Red LED, for negative half cycle use Green LED). Also compute the time for which each LED is switched on in one minute

    • Tony Walton

      Not sure how much use that would be. The human eye can’t see individual images faster than about 24 images per second. LEDs at mains frequency (50Hz/60Hz) arranged the way you say would just look like a combination of the two colours: yellow, if you used red and green.

    • Wayne Storr

      Clearly each LED would be “ON” only when forward biased every half-cycle for a time dependant on the period of the waveform

  • Kiran patil

    I want to learn about led, smd light

  • Marc DTM

    Someone would have a circuit plan for a 120V led driver
    Thanks in advance

  • Harish Srivastava

    I connected 16 red led in series and made a slide,i connected another 16led in series and made two more slides.
    Now i’m connecting negative end of each slide and leaving the positive end aprt from each other and giving supply for each slide so that i can light up the slides saperatly but when i give the supply, the other two slides also get light up..why it is so please explain me……

    • DJ Ron

      Did you put a current limiting resistor in each string? Sometimes, LED forward voltage drops vary enough to create a race condition, whereby they turn on differently that expected. By “slides”, I assume you mean a (slide) switch. The problem with series is if one LED fails, the whole string goes off. You may be better with a series parallel arrangement of say 3 in series with a series resistor, and 5 groups of them in parallel, which is 15 LEDs (not 14), but, you can control them better. Good luck

  • James Chappell

    what is the wave form of the light emitted? Sinusoidal or square?

  • Karis ndungu

    This is the best tutorial for LEDs. Don’t know what I could have done with my project without it.

    Thanks a million

  • Krishan Singal

    Great tutorial. Well said, clear, enjoyed and learned at the same time !

    Thanks

  • mathan

    why the LED illumination getting low when it got older.

  • Rohit

    Few problems questions solved

  • Dwight Collman, MD

    what formulation [doping] produces 222 nm wavelength … ? Any references?

    please send them to me if known. I’m looking for experts in far UVC led manufacturing. Contact me by email 1st please.

    thank you.

    D Collman